-
Digital industrial platform scale with a 150 kg capacity, 10 g display increments and a 30 × 40 cm stainless-steel weighing surface. -
TPR-3005-2D dual-channel adjustable bench DC power supply, with a listed output range of 0–30 V and 0–5 A. -
Belt-driven, twin-cylinder air compressor with an 80 L tank, a 2.2 kW motor and a listed pressure of 8 bar. -
Out of stock
VORTEX WL-2200 centrifugal blower for pressure or vacuum service, rated at 2.2 kW for a 380 V three-phase supply. -
80 W IP68 submersible water pump for 220 V AC, with a listed flow rate of 3,500 L/h and a maximum lift of 3.5 m. -
YH200 LED digital readout for milling machines, lathes, grinders and boring machines, with 2- and 3-axis configurations listed. -
ZX7-250 compact 220 V IGBT inverter for DC stick welding, with a digital current display, hot start and anti-stick. -
High torque closed loop servo motor. DIY CNC Machines,Milling machines,lathe,pick and place machines.1000W 3.2 N.M -
90ST-M04025 1 kW AC servo kit with a 2,500 rpm motor, matching drive and 3 m motor and encoder cables. -
FQD 3.2 kW water-cooled CNC spindle with an ER20 collet interface and a listed speed of 24,000 rpm. -
Out of stock
FQD 4.5 kW square air-cooled CNC spindle with an ER32 collet interface and a listed speed of 24,000 rpm. -
Female-thread spherical rod end for articulated linkages, with M6 or M8 thread options and left- or right-hand variants. -
Round air-cooled CNC spindle with an aluminium mount and listed 0.8, 1.5 and 2.2 kW configurations. -
2.2 kW square air-cooled CNC spindle with a listed 220 V rating and an ER20 collet system. -
Out of stock
Normally closed two-wire motorised brass ball valve, listed in DN20 and DN25 sizes with 12 V and 24 V options. -
SAKO SKI780 2.2 kW variable-frequency drive with three-phase motor output and 220 V or 380 V configurations. -
DT9205A handheld digital multimeter with manual range selection, a 1,999-count LCD and dedicated diode and transistor test functions. -
XB2-BS542C red twist-release emergency-stop pushbutton for a 22 mm panel cutout, with one NO and one NC contact. -
Hardened module 1.5 helical gear rack, 1 m long, with a 17 × 17 mm cross-section. -
20100 aluminium V-slot extrusion, 20 × 100 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
2020 aluminium V-slot extrusion, 20 × 20 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
Out of stock
2040 aluminium V-slot extrusion, 20 × 40 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
2060 aluminium V-slot extrusion, 20 × 60 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
30150W aluminium V-slot extrusion, 30 × 150 mm cross-section, 2,000 mm long with nominal 8 mm grooves. -
Pair of AD110 passive two-way speaker crossovers for routing low and high frequencies to separate drivers. -
1/2-inch brass ball valve with a steel lever for manual shutoff in a compatible line. -
Walfront four-axis USB motion controller for Mach3 on Windows, with a maximum step-pulse frequency of 100 kHz and a 0–10 V spindle control output. -
5:1 gearbox for compatible NEMA 34 CNC rack drives, with a listed 14 mm keyed shaft. -
DANSHENG 10-inch dual-voice-coil speaker with a listed 4 Ω impedance and 120 W rating. -
A five-axis Mach3 breakout board for parallel-port CNC control. Connection and operating details are listed below.
-
DS18B20 digital temperature probe with a 1 m cable and a 1-Wire interface. -
DS18B20 digital temperature probe with an M8 × 1 thread, a 1 m cable and a 1-Wire interface. -
Panel timer relay for delayed or cyclic switching. Match the exact model, supply voltage and socket to the installation. -
SMART SENSOR AT380 non-contact infrared surface thermometer with a listed range of −32 to 380 °C.
