-
T12 trapezoidal lead screw with a brass nut for 3D printers and CNC mechanisms, available in 500 mm and 1,000 mm lengths. -
ZTS-series DC-controlled AC solid-state relay with aluminium heatsink, available in 25 A and 60 A versions. -
MAL-series pneumatic cylinder with an aluminium-alloy body and a single piston rod. -
HG-series recirculating linear guide blocks in sizes 15, 20 and 25, available in HGH-CA square or HGW-CC flanged form. -
Right-hand 12 V power-window gearmotor with a square output shaft and a four-hole mounting pattern. -
DS-9018 compact numeric keypad with a PS/2 connector for compatible computers and equipment. -
GA37RG two-wire DC gearmotor, rated 12 V with a listed output speed of 150 rpm and a 37 mm body diameter. -
KTV horn tweeter with a 150 × 150 mm front face and an 80 mm magnet. -
Two-channel DIN-rail relay module with optocoupler isolation, selectable high- or low-level triggering and screw terminals. -
Metric twist drill set covering diameters from 1 to 10 mm, in DIN 338 form for metalworking. -
DSG16H aluminium ball-nut housing for mounting an SFU1605 ball nut to a CNC carriage or moving plate. -
REX-C700 panel-mount PID temperature controller with type K sensor input, SSR control output and a type K probe. -
68KTYZ 220 V AC synchronous motor with an 8 mm shaft and listed 30 rpm and 60 rpm options. -
Four-channel summing junction box for load cells, with individual signal trimming and one combined output. -
SMART SENSOR AT380 non-contact infrared surface thermometer with a listed range of −32 to 380 °C. -
Openable 1 m cable carrier with 25 × 38 mm internal clearance and an R100 bend radius, with end connectors. -
Electronic edge finder with LED and audible indication for locating a conductive workpiece on a milling machine. -
LT4 self-returning machine foot switch in an aluminium housing with one normally open and one normally closed contact. -
36 V DC, 6 A power supply in the listed 200 W class for compatible CNC equipment and LED lighting. -
SBW-430 8-inch woofer with a 4 Ω impedance, listed 150 W rating and a 30 oz magnet. -
QRB1 photoresistive flame detector for compatible burner control systems. -
AFR-2000 compressed-air filter and regulator with 1/4-inch ports, a pressure gauge and a mounting bracket. -
Schneider LC1N1210 AC contactor rated at 12 A, with 24 V AC and 110 V AC coil variants listed. -
150 mm stainless-steel digital caliper with metric, inch and fractional-inch display modes for inside, outside, step and depth measurements. -
GD-60S stem-mount levelling caster with a swivel wheel and an adjustable support foot. Supplied individually. -
Two-way passive speaker crossover boards for separating high and low frequencies, supplied as a pair. -
LTH-1/6 self-returning aluminium foot switch with one normally open and one normally closed contact. -
Openable 1 m cable carrier with 35 × 50 mm internal clearance and an R150 bend radius, with end connectors. -
QRB1 photoresistive flame detector for compatible burner control systems. -
Three-wire electric actuator for compatible ball valves, available in 220 V AC and 12–24 V DC versions. -
YDT1-16 dual momentary foot switch with two pedals, each with one normally open and one normally closed contact. -
PT50-3T-DJ foldable 24 V DC signal tower with red, amber and green LED segments. -
24 V DC, 50 W geared motor for compatible window, wiper and custom linkage mechanisms. -
80 W IP68 submersible water pump for 220 V AC, with a listed flow rate of 3,500 L/h and a maximum lift of 3.5 m. -
HM12-57 C7 aluminium motor bracket with an integrated bearing seat for a compatible screw-driven CNC axis. -
ISO25 toolholder for ER20 collets, made from hardened 20CrMnTi steel for compatible CNC spindles. -
ISO20–ER20 collet toolholder for compatible CNC spindles, designed to clamp round-shank tools in an ER20 collet. -
220 V AC, 500 W alumina ceramic igniter for compatible pellet and biomass burners, with an M16 × 1.5 thread. -
DANSHENG 10-inch dual-voice-coil speaker with a listed 4 Ω impedance and 120 W rating. -
5718HB56 two-phase NEMA 23 stepper motor with a 56 mm body, 8 mm shaft and 1.8° step angle. -
NDR-120-24 DIN-rail AC-to-DC power supply with a 24 V DC, 5 A output (120 W) for CNC and control-panel applications. -
BK12 fixed-end and BF12 floating-end ball screw supports for SFU1605, SFU1610 or SFU1616 screws with matching machined ends. -
Out of stock
2040 aluminium V-slot extrusion, 20 × 40 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
Walfront four-axis USB motion controller for Mach3 on Windows, with a maximum step-pulse frequency of 100 kHz and a 0–10 V spindle control output. -
HGR-profile linear guide rail in sizes 15, 20 and 25, with 1 m, 2 m and 3 m lengths listed. -
Out of stock
24 V DC, 20 A power supply in the listed 500 W class for compatible CNC equipment and LED lighting. -
Pair of AD110 passive two-way speaker crossovers for routing low and high frequencies to separate drivers. -
4V220-08 double-solenoid pneumatic valve with a 24 V DC coil supply and a five-port, two-position configuration. -
GS937D digital soldering station with LED temperature display, adjustable temperature and a replaceable iron tip and heater. -
Openable 1 m cable carrier with 45 × 100 mm internal clearance and an R200 bend radius, with end connectors. -
60 V DC, 6.7 A power supply in the listed 400 W class for compatible CNC equipment and LED lighting. -
The YIHUA 937D is a digital soldering station with a replaceable tip and heating element, antistatic design and a slim handpiece.
-
Out of stock
A normally closed CNC Z-axis tool presetter with a 5 mm stroke, 1.5 N contact force and an IP67 enclosure.
-
Out of stock
DYLY-103 S-type load cell for tension and compression, rated 100 kg with nominal sensitivity of 2.0 mV/V. -
KTV 10-inch speaker with an 8 Ω impedance, listed 200 W rating and 140 mm magnet. -
The YIHUA 936D is a digital soldering station with a replaceable tip and heating element, antistatic design and a slim handpiece.
-
2060 aluminium V-slot extrusion, 20 × 60 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
Digital industrial platform scale with a 150 kg capacity, 10 g display increments and a 30 × 40 cm stainless-steel weighing surface. -
SN50T3 cyclone dust separator with a flanged base and a 55 mm outlet, for compatible vacuums and extraction systems. -
Two-way motorised brass ball valve with a three-wire actuator, available in DN20, DN25, DN40 and DN50 sizes. -
13-piece ER20 AA spring collet set for round tool shanks from 1 to 13 mm. -
DPT10-23-30 two-speed inline ventilation fan for 100 mm ducting, with a 37 W single-phase motor. -
Hardened module 1.5 helical gear rack, 1 m long, with a 17 × 17 mm cross-section. -
21 V brushless cordless impact drill with a 2.0 Ah lithium-ion battery, a 2–10 mm metal chuck and a listed torque of 85 N·m. -
Vertical centrifugal machine coolant pump rated at 40 W, with a listed maximum flow of 12 L/min and a maximum head of 3.5 m. -
4-inch machine vise with a cast-iron body, steel jaws and an opening of up to 100 mm for milling and drilling. -
NMRV30 right-angle worm gearbox for compatible NEMA 23 motors, supplied with an adapter and a 14 mm keyed shaft. -
DOB-12/40W single-phase machine-tool coolant pump with a 40 W motor. -
SFU1605 ball screw kit with a 400 mm overall length, 290 mm usable travel, BK/BF supports, DSG16 housing and an 8 × 10 mm coupling. -
Planetary gearbox for a compatible NEMA 23 motor, with an 8 mm input bore and a 14 mm output shaft. -
Out of stock
Normally closed two-wire motorised brass ball valve, listed in DN20 and DN25 sizes with 12 V and 24 V options. -
24 V DC, 25 A, 600 W power supply for compatible CNC equipment and LED lighting. -
ZX7-250 compact 220 V IGBT inverter for DC stick welding, with a digital current display, hot start and anti-stick. -
24 V linear actuator with a 200 mm stroke, listed 500 N force and a speed of 20 mm/s. -
20100 aluminium V-slot extrusion, 20 × 100 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
Out of stock
16-piece ER25 AA spring collet set for round tool shanks from 1 to 16 mm. -
Optical linear scale for compatible DRO systems, available with nominal measuring travel from 100 to 700 mm. -
5:1 gearbox for compatible NEMA 34 CNC rack drives, with a listed 14 mm keyed shaft.
