-
Round air-cooled CNC spindle with an aluminium mount and listed 0.8, 1.5 and 2.2 kW configurations. -
2.2 kW square air-cooled CNC spindle with a listed 220 V rating and an ER20 collet system. -
Out of stock
Normally closed two-wire motorised brass ball valve, listed in DN20 and DN25 sizes with 12 V and 24 V options. -
SAKO SKI780 2.2 kW variable-frequency drive with three-phase motor output and 220 V or 380 V configurations. -
DT9205A handheld digital multimeter with manual range selection, a 1,999-count LCD and dedicated diode and transistor test functions. -
XB2-BS542C red twist-release emergency-stop pushbutton for a 22 mm panel cutout, with one NO and one NC contact. -
Hardened module 1.5 helical gear rack, 1 m long, with a 17 × 17 mm cross-section. -
20100 aluminium V-slot extrusion, 20 × 100 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
2020 aluminium V-slot extrusion, 20 × 20 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
Out of stock
2040 aluminium V-slot extrusion, 20 × 40 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
2060 aluminium V-slot extrusion, 20 × 60 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
30150W aluminium V-slot extrusion, 30 × 150 mm cross-section, 2,000 mm long with nominal 8 mm grooves. -
Pair of AD110 passive two-way speaker crossovers for routing low and high frequencies to separate drivers. -
1/2-inch brass ball valve with a steel lever for manual shutoff in a compatible line. -
Walfront four-axis USB motion controller for Mach3 on Windows, with a maximum step-pulse frequency of 100 kHz and a 0–10 V spindle control output. -
5:1 gearbox for compatible NEMA 34 CNC rack drives, with a listed 14 mm keyed shaft. -
DANSHENG 10-inch dual-voice-coil speaker with a listed 4 Ω impedance and 120 W rating. -
A five-axis Mach3 breakout board for parallel-port CNC control. Connection and operating details are listed below.
-
DS18B20 digital temperature probe with a 1 m cable and a 1-Wire interface. -
DS18B20 digital temperature probe with an M8 × 1 thread, a 1 m cable and a 1-Wire interface. -
Panel timer relay for delayed or cyclic switching. Match the exact model, supply voltage and socket to the installation. -
SMART SENSOR AT380 non-contact infrared surface thermometer with a listed range of −32 to 380 °C. -
KTV horn tweeter with a 150 × 150 mm front face and an 80 mm magnet. -
KTV 10-inch speaker with an 8 Ω impedance, listed 200 W rating and 140 mm magnet. -
650 nm red cross-line laser module with a listed 5 mW output for alignment and centring. -
24 V linear actuator with a 200 mm stroke, listed 500 N force and a speed of 20 mm/s. -
LT4 self-returning machine foot switch in an aluminium housing with one normally open and one normally closed contact. -
LTH-1/6 self-returning aluminium foot switch with one normally open and one normally closed contact. -
PG7 nylon cable gland for round cables with a 2–5 mm outside diameter, with a compression seal and panel locknut. -
SSW806 6.5-inch woofer with an 8 Ω impedance, listed 80 W rating and a 24 oz magnet. -
SBW424 6.5-inch woofer with a 4 Ω impedance, listed 120 W rating and gold-plated terminals. -
SBW-430 8-inch woofer with a 4 Ω impedance, listed 150 W rating and a 30 oz magnet. -
NEMA 34 closed-loop stepper motor and drive kit with a listed 12.5 N·m holding torque and a 1,000 PPR encoder. -
Vishay TCRT5000 reflective infrared sensor with a phototransistor output for short-range object and contrast detection. -
TFS-201 momentary foot pedal switch with one normally open and one normally closed contact and a 1 m cable. -
Two-way passive speaker crossover boards for separating high and low frequencies, supplied as a pair. -
A four-axis USB motion controller for Mach3, with a maximum step-pulse frequency of 100 kHz. Connection and operating details are listed below.
-
VORTEX HG-750 centrifugal blower for pressure or vacuum service, with a 750 W motor and a listed maximum airflow of 147 m³/h. -
YDT1-16 dual momentary foot switch with two pedals, each with one normally open and one normally closed contact. -
YTUM K11-125 125 mm three-jaw self-centering lathe chuck for compatible spindle mounts. -
50 W neutral-white LED floodlight with a 4000 K colour temperature, IP66 aluminium housing and adjustable mounting bracket. -
ISO20–ER20 collet toolholder for compatible CNC spindles, designed to clamp round-shank tools in an ER20 collet. -
ISO25 toolholder for ER20 collets, made from hardened 20CrMnTi steel for compatible CNC spindles. -
433 MHz wireless remote-control set with 12 V single-channel and 5 V two-channel relay receiver options. -
5718HB56 two-phase NEMA 23 stepper motor with a 56 mm body, 8 mm shaft and 1.8° step angle. -
HM12-57 C7 aluminium motor bracket with an integrated bearing seat for a compatible screw-driven CNC axis. -
D30L40 flexible jaw coupling with 8 mm and 10 mm bores, a 30 mm outside diameter and a 40 mm overall length. -
DSG16H aluminium ball-nut housing for mounting an SFU1605 ball nut to a CNC carriage or moving plate. -
IPXM102 straight machine torch for CNC plasma systems with a compatible non-HF ignition system. -
100 mm flat ribbon cable with a female 10-pin IDC connector at each end. -
SMR1602AA-VA character LCD with two lines of 16 green characters on a black background and a parallel interface. -
2.2 kW variable-frequency drive for compatible three-phase motors, with separate 220 V and 380 V configurations. -
-
Stepper Motor Actuator|High-Precision Travel Stroke:Experience smooth motion with a 200-500mm effective travel stroke, ensuring precise linear motion for CNC applications.
-
-
68KTYZ 220 V AC synchronous motor with an 8 mm shaft and listed 30 rpm and 60 rpm options. -
Right-hand 12 V power-window gearmotor with a square output shaft and a four-hole mounting pattern. -
24 V DC, 50 W geared motor for compatible window, wiper and custom linkage mechanisms. -
220 V AC SCR voltage regulator with 100 adjustment levels and a listed 4,000 W limit for resistive loads. -
220 V AC adjustable voltage regulator with a listed 4,000 W maximum for resistive loads. -
ASAIR AM2302 (DHT22) digital sensor for relative humidity and air temperature, in a four-pin package. -
DF-2 centrifugal blower with a 120 W motor for a 220 V AC supply. -
GX16 and GX20 circular plug-and-socket connectors in 4-, 6- and 10-contact configurations, subject to the selected variant. -
4 × 4 matrix keypad with an 8-pin, 2.54 mm-pitch connector for compatible control boards. -
MAX6675 digital interface module with a K-type thermocouple, SPI output and cold-junction compensation. -
Out of stock
Compact desktop conveyor with a 10 × 50 cm PVC belt and speed adjustment, with forward, reverse and stop controls. -
Openable 1 m cable carrier with 25 × 38 mm internal clearance and an R100 bend radius, with end connectors. -
Openable 1 m cable carrier with 35 × 50 mm internal clearance and an R150 bend radius, with end connectors. -
Openable 1 m cable carrier with 45 × 100 mm internal clearance and an R200 bend radius, with end connectors. -
Out of stock
Openable 1 m cable carrier with 18 × 18 mm internal clearance and an R70 bend radius. -
DIN-rail galvanically isolated half-duplex TTL-to-RS485 converter for 3.3–5 V TTL signals.
