-
Two-position KF129 screw terminal block for through-hole PCB mounting, with 5.08 mm pin spacing. -
Three-position KF129 PCB screw terminal block for a removable connection between field wires and a circuit board. -
PG7 nylon cable gland for round cables with a 2–5 mm outside diameter, with a compression seal and panel locknut. -
PC817 through-hole optocoupler in a four-pin DIP package, with an infrared LED input and a phototransistor output. -
0912-series power inductor in a 9 × 12 mm package, supplied individually. -
Vishay TCRT5000 reflective infrared sensor with a phototransistor output for short-range object and contrast detection. -
Stainless-steel clamping screw with a star-shaped hand knob, available in M4, M6, M8 and M10 thread sizes. -
SRD-series five-pin PCB relay. Confirm the coil voltage on the supplied relay and match it to the control circuit. -
MAX7219EWG serial display driver in a 24-pin wide SOIC package for up to eight common-cathode LED digits or 64 individual LEDs. -
B0505S-1W isolated DC–DC converter with nominal 5 V input and output and 1 W output power. -
100 mm flat ribbon cable with a female 10-pin IDC connector at each end. -
4 × 4 matrix keypad with an 8-pin, 2.54 mm-pitch connector for compatible control boards. -
GX16 and GX20 circular plug-and-socket connectors in 4-, 6- and 10-contact configurations, subject to the selected variant. -
Plug-in relay socket for a compatible MY4NJ control relay, with wiring terminals for the relay coil and contacts. -
DS18B20 digital temperature probe with a 1 m cable and a 1-Wire interface. -
ER20 Type A collet nut for a compatible ER20 chuck or toolholder. Supplied individually. -
Two-channel PC817 optocoupler board for isolating low-frequency control signals, with independent channels and jumper-selectable output logic. -
EC11 incremental rotary encoder with an integrated push switch, listed with 20 detents and 20 pulses per revolution. -
KP pillow-block and KFL flanged mounted bearings with zinc-alloy housings, available in multiple shaft bore sizes. -
ER16M mini-style collet nut for compatible ER16 toolholders and spindle noses. -
LA38 three-position rotary selector switch for control panels, with one normally open and one normally closed contact. -
Height-adjustable machine levelling foot with a rubber base, ball joint and threaded stem. -
K-type thermocouple with a threaded stainless-steel probe and a listed range of 0–600 °C. -
XB2-BS542C red twist-release emergency-stop pushbutton for a 22 mm panel cutout, with one NO and one NC contact. -
XL4015 DC-to-DC step-down module with adjustable constant-voltage and constant-current modes, rated up to 5 A. -
Out of stock
Detection distance 5MM. Operating voltage: DC: DC6 ~ 36V or DC12V-DC24V Output Type: NPN type Output status: normally open Detection of objects: Metal objects are welcome to use -
Black nylon hinge, 40 × 40 × 9 mm, for compatible enclosures, cabinets and furniture. -
LA42DWQ-22 panel-mount rotary potentiometer, available in 5 kΩ and 10 kΩ versions. -
Three-digit red seven-segment LED module with 0.5-inch digits and a 74HC595 serial shift-register interface. -
ASAIR AM2302 (DHT22) digital sensor for relative humidity and air temperature, in a four-pin package. -
ATmega8-16AU 8-bit AVR microcontroller in a 32-pin TQFP package, with 8 KB of flash program memory. -
JQX-15F (T90) PCB power relay, 1Z changeover configuration, with 5 V, 12 V and 24 V DC coil options. -
650 nm red cross-line laser module with a listed 5 mW output for alignment and centring. -
Latching red mushroom-head emergency-stop pushbutton with a 40 mm head and one normally closed contact. -
Out of stock
OMCH SN04-N inductive proximity sensor with a three-wire, normally open NPN output and a 6–36 V DC supply, as marked on the sensor. -
Female-thread spherical rod end for articulated linkages, with M6 or M8 thread options and left- or right-hand variants. -
SMR1602AA-VA character LCD with two lines of 16 green characters on a black background and a parallel interface. -
Eight-digit red seven-segment LED module with a MAX7219 serial display driver and programmable brightness. -
50 g spool of Sn60/Pb40 rosin-core solder wire, available in 0.5 mm or 1.0 mm diameter. -
DS18B20 digital temperature probe with an M8 × 1 thread, a 1 m cable and a 1-Wire interface. -
433 MHz wireless remote-control set with 12 V single-channel and 5 V two-channel relay receiver options. -
Type : Bridge type can-open drag chain Material : Plastic PA66 Length : 1000mm Inner height : 15mm-25mm Inner width : 15mm-38mm-77mmBending radius : 55mm , 100mm , 150mm , 200mm
View full size 
View full size
View full size
Price for 1Meter Length -
1/2-inch brass ball valve with a steel lever for manual shutoff in a compatible line. -
MY4NJ plug-in control relay with selectable 12 V DC, 24 V DC or 220 V AC coil. Use a compatible MY4NJ socket. -
TFS-201 momentary foot pedal switch with one normally open and one normally closed contact and a 1 m cable. -
ATmega128-16AU 8-bit AVR microcontroller with 128 KB of flash in a 64-pin TQFP package. -
LJ12A3 Z/BX inductive proximity sensor with a normally open output for detecting metal targets. -
D30L40 flexible jaw coupling with 8 mm and 10 mm bores, a 30 mm outside diameter and a 40 mm overall length. -
LTE-1101J industrial LED warning beacon with an audible alarm for equipment and work-area signalling. -
Sale!
AC-to-DC power supply with a 12 V DC, 10 A output (120 W) for compatible CNC equipment and LED lighting. -
46-piece ratchet tool set supplied in a thermoplastic storage case for workshop and vehicle maintenance. -
MAX6675 digital interface module with a K-type thermocouple, SPI output and cold-junction compensation. -
USBasp 5 V AVR in-system programmer in a case, with a 10-pin ISP cable. -
50 W neutral-white LED floodlight with a 4000 K colour temperature, IP66 aluminium housing and adjustable mounting bracket. -
DB25 male D-sub breakout adapter with screw terminals for connecting individual wires without soldering. -
Galvanically isolated TTL-to-RS485 PCB module for 3.3 V or 5 V logic, with receive and transmit indicators. -
The ME-8108 is a momentary limit switch with an adjustable roller lever for detecting machine position.
-
Four ME-8111 momentary limit switches with a direct-action plunger and one normally open and one normally closed contact per switch. -
220 V AC SCR voltage regulator with 100 adjustment levels and a listed 4,000 W limit for resistive loads. -
DT9205A handheld digital multimeter with manual range selection, a 1,999-count LCD and dedicated diode and transistor test functions. -
HY-100 rosin paste flux for preparing PCB pads and component leads before hand soldering. Net contents 100 g. -
DIN-rail power supply with listed 5 V DC, 3 A and 24 V DC, 0.6 A output configurations. -
Panel timer relay for delayed or cyclic switching. Match the exact model, supply voltage and socket to the installation. -
Out of stock
Openable 1 m cable carrier with 18 × 18 mm internal clearance and an R70 bend radius. -
A five-axis Mach3 breakout board for parallel-port CNC control. Connection and operating details are listed below.
-
Model 907 replacement soldering iron handpiece, listed at 24 V DC and 50 W, with a five-pin connector. -
TB6600 single-axis stepper driver with a listed 9–42 V DC supply range, adjustable microstepping and up to 4 A output. -
SSR-1 D4825 25 A solid-state relay for switching a single-phase AC load from a 3–32 V DC control signal. -
SSW806 6.5-inch woofer with an 8 Ω impedance, listed 80 W rating and a 24 oz magnet. -
Sale!
24 V DC, 8.5 A power supply in the listed 200 W class for compatible CNC equipment and LED lighting.
-
2020 aluminium V-slot extrusion, 20 × 20 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
DIN-rail galvanically isolated half-duplex TTL-to-RS485 converter for 3.3–5 V TTL signals. -
Out of stock
24 V DC, 2.5 A DIN-rail power supply for compatible CNC equipment and control panels. -
SBW424 6.5-inch woofer with a 4 Ω impedance, listed 120 W rating and gold-plated terminals. -
ZHENGKE ZGA28RO two-terminal DC gearmotor, listed for 12 V DC and 400 rpm output. -
220 V AC adjustable voltage regulator with a listed 4,000 W maximum for resistive loads. -
AR2000-series compressed-air pressure regulator with a 1/4-inch NPT connection, gauge and mounting bracket. -
A four-axis USB motion controller for Mach3, with a maximum step-pulse frequency of 100 kHz. Connection and operating details are listed below.
-
DM556 digital stepper drive with optically isolated inputs, adjustable microstepping and up to 5.6 A output.
