-
JetCut CNC plasma torch height controller with UP/DOWN/OK and Step/Direction interfaces, arc-voltage feedback and Anti-Dive. -
JetCut CNC plasma torch height controller with UP/DOWN/OK and Step/Direction interfaces, arc-voltage feedback and Anti-Dive.
-
ALPHA THC SD uses arc-voltage feedback to adjust CNC plasma torch height through Step/Direction and includes an Anti-Dive input. -
GX16 and GX20 circular plug-and-socket connectors in 4-, 6- and 10-contact configurations, subject to the selected variant. -
B0505S-1W isolated DC–DC converter with nominal 5 V input and output and 1 W output power. -
DS18B20 digital temperature probe with a 1 m cable and a 1-Wire interface. -
100 mm flat ribbon cable with a female 10-pin IDC connector at each end. -
JQX-15F (T90) PCB power relay, 1Z changeover configuration, with 5 V, 12 V and 24 V DC coil options. -
DM556 digital stepper drive with optically isolated inputs, adjustable microstepping and up to 5.6 A output. -
220 V AC SCR voltage regulator with 100 adjustment levels and a listed 4,000 W limit for resistive loads. -
TFS-201 momentary foot pedal switch with one normally open and one normally closed contact and a 1 m cable. -
LJ12A3 Z/BX inductive proximity sensor with a normally open output for detecting metal targets. -
Out of stock
OMCH SN04-N inductive proximity sensor with a three-wire, normally open NPN output and a 6–36 V DC supply, as marked on the sensor. -
0912-series power inductor in a 9 × 12 mm package, supplied individually. -
Height-adjustable machine levelling foot with a rubber base, ball joint and threaded stem. -
2020 aluminium V-slot extrusion, 20 × 20 mm cross-section, 2,000 mm long with nominal 6 mm grooves. -
433 MHz wireless remote-control set with 12 V single-channel and 5 V two-channel relay receiver options. -
TB6600 single-axis stepper driver with a listed 9–42 V DC supply range, adjustable microstepping and up to 4 A output. -
XB2-BS542C red twist-release emergency-stop pushbutton for a 22 mm panel cutout, with one NO and one NC contact. -
Sale!
ArcShine CNC plasma torch height controller with isolated UP/DOWN/OK outputs and 0–10 V remote target-voltage adjustment. -
AQTRONIC DSC3 digital ohmic sensor for CNC plasma cutting, with 100 sensitivity settings and a 24 V DC supply. -
XL4015 DC-to-DC step-down module with adjustable constant-voltage and constant-current modes, rated up to 5 A. -
LA38 three-position rotary selector switch for control panels, with one normally open and one normally closed contact. -
Openable 1 m cable carrier with 35 × 50 mm internal clearance and an R150 bend radius, with end connectors. -
Out of stock
DYLY-103 S-type load cell for tension and compression, rated 100 kg with nominal sensitivity of 2.0 mV/V. -
Three-digit red seven-segment LED module with 0.5-inch digits and a 74HC595 serial shift-register interface. -
DIN-rail power supply with listed 5 V DC, 3 A and 24 V DC, 0.6 A output configurations. -
36 V DC, 6 A power supply in the listed 200 W class for compatible CNC equipment and LED lighting. -
LA42DWQ-22 panel-mount rotary potentiometer, available in 5 kΩ and 10 kΩ versions. -
PC817 through-hole optocoupler in a four-pin DIP package, with an infrared LED input and a phototransistor output. -
Panel timer relay for delayed or cyclic switching. Match the exact model, supply voltage and socket to the installation. -
50 W neutral-white LED floodlight with a 4000 K colour temperature, IP66 aluminium housing and adjustable mounting bracket. -
SGX CNC linear module using a 1610 ball screw with 10 mm movement per turn and a NEMA 23 motor bracket. -
JYV5 variable-frequency drive for compatible three-phase motors, with 2.2, 5.5 and 7.5 kW configurations listed. -
The ME-8108 is a momentary limit switch with an adjustable roller lever for detecting machine position.
-
Sale!
24 V DC, 8.5 A power supply in the listed 200 W class for compatible CNC equipment and LED lighting. -
MY4NJ plug-in control relay with selectable 12 V DC, 24 V DC or 220 V AC coil. Use a compatible MY4NJ socket. -
2.2 kW variable-frequency drive for compatible three-phase motors, with separate 220 V and 380 V configurations. -
A five-axis Mach3 breakout board for parallel-port CNC control. Connection and operating details are listed below.
-
Latching red mushroom-head emergency-stop pushbutton with a 40 mm head and one normally closed contact. -
Sale!
ZetaStar CNC plasma torch height controller with arc-voltage feedback, optically isolated outputs and a 2.4-inch TFT display. -
Lichuan NEMA 23 closed-loop kit with a 3 N·m three-phase stepper motor, encoder and LCDA357H driver. -
Two-channel PC817 optocoupler board for isolating low-frequency control signals, with independent channels and jumper-selectable output logic. -
ASAIR AM2302 (DHT22) digital sensor for relative humidity and air temperature, in a four-pin package. -
MAX6675 digital interface module with a K-type thermocouple, SPI output and cold-junction compensation. -
K-type thermocouple with a threaded stainless-steel probe and a listed range of 0–600 °C. -
68KTYZ 220 V AC synchronous motor with an 8 mm shaft and listed 30 rpm and 60 rpm options. -
650 nm red cross-line laser module with a listed 5 mW output for alignment and centring. -
LT4 self-returning machine foot switch in an aluminium housing with one normally open and one normally closed contact. -
Vishay TCRT5000 reflective infrared sensor with a phototransistor output for short-range object and contrast detection. -
NEMA 34 closed-loop stepper motor and drive kit with a listed 12.5 N·m holding torque and a 1,000 PPR encoder. -
Walfront four-axis USB motion controller for Mach3 on Windows, with a maximum step-pulse frequency of 100 kHz and a 0–10 V spindle control output. -
SUSWE 290 variable-frequency drive with listed 220 V input and 380 V output, available in 2.2 and 4.0 kW versions. -
NMRV30 right-angle worm gearbox for compatible NEMA 23 motors, supplied with an adapter and a 14 mm keyed shaft. -
DS-9018 compact numeric keypad with a PS/2 connector for compatible computers and equipment. -
USBasp 5 V AVR in-system programmer in a case, with a 10-pin ISP cable. -
50 g spool of Sn60/Pb40 rosin-core solder wire, available in 0.5 mm or 1.0 mm diameter. -
EC11 incremental rotary encoder with an integrated push switch, listed with 20 detents and 20 pulses per revolution. -
DT9205A handheld digital multimeter with manual range selection, a 1,999-count LCD and dedicated diode and transistor test functions. -
DSG16H aluminium ball-nut housing for mounting an SFU1605 ball nut to a CNC carriage or moving plate. -
TP06 electronic touch probe for locating workpiece edges, centres and reference surfaces on compatible Mach3 or Grbl systems. -
Out of stock
Detection distance 5MM. Operating voltage: DC: DC6 ~ 36V or DC12V-DC24V Output Type: NPN type Output status: normally open Detection of objects: Metal objects are welcome to use -
Out of stock
A normally closed CNC Z-axis tool presetter with a 5 mm stroke, 1.5 N contact force and an IP67 enclosure.
-
SFU1605 ball screw kit with a 400 mm overall length, 290 mm usable travel, BK/BF supports, DSG16 housing and an 8 × 10 mm coupling. -
DB25 male D-sub breakout adapter with screw terminals for connecting individual wires without soldering. -
HGR-profile linear guide rail in sizes 15, 20 and 25, with 1 m, 2 m and 3 m lengths listed. -
4-inch machine vise with a cast-iron body, steel jaws and an opening of up to 100 mm for milling and drilling. -
VORTEX HG-750 centrifugal blower for pressure or vacuum service, with a 750 W motor and a listed maximum airflow of 147 m³/h. -
Galvanically isolated TTL-to-RS485 PCB module for 3.3 V or 5 V logic, with receive and transmit indicators. -
DS18B20 digital temperature probe with an M8 × 1 thread, a 1 m cable and a 1-Wire interface. -
Out of stock
Normally closed two-wire motorised brass ball valve, listed in DN20 and DN25 sizes with 12 V and 24 V options. -
60 V DC, 6.7 A power supply in the listed 400 W class for compatible CNC equipment and LED lighting. -
Out of stock
24 V DC, 20 A power supply in the listed 500 W class for compatible CNC equipment and LED lighting. -
GS937D digital soldering station with LED temperature display, adjustable temperature and a replaceable iron tip and heater. -
The YIHUA 936D is a digital soldering station with a replaceable tip and heating element, antistatic design and a slim handpiece.
-
A four-axis USB motion controller for Mach3, with a maximum step-pulse frequency of 100 kHz. Connection and operating details are listed below.
-
Novusun NVEM Ethernet motion controller for Mach3, with a listed maximum pulse frequency of 200 kHz per axis. -
Type : Bridge type can-open drag chain Material : Plastic PA66 Length : 1000mm Inner height : 15mm-25mm Inner width : 15mm-38mm-77mmBending radius : 55mm , 100mm , 150mm , 200mm
View full size 
View full size
View full size
Price for 1Meter Length -
60AST-A1C01930 three-phase closed-loop servo kit with a 600 W motor, 1.91 Nm rated torque and a matching drive. -
DOB-12/40W single-phase machine-tool coolant pump with a 40 W motor. -
Out of stock
16-piece ER25 AA spring collet set for round tool shanks from 1 to 16 mm. -
Model 907 replacement soldering iron handpiece, listed at 24 V DC and 50 W, with a five-pin connector.
